So you’ve made some wings with your Hot Wire CNC Foam Cutter and wondered if you can make fuselages as well I’ve been on that journey to and now I can share my knowledge and experience.
I purchased DevFus Foam a few years ago and now there is a second release. In my opinion its the best software for creating fuselages. I did look for other options like Jedicut which you could make a fuselage with. It will cut any shape from two profiles but you will need to lots of design work to create all the profiles.
I’ve made a Hawker Hurricane using the previous version of DevFus Foam and it was a challenge but turned out better than I imagined. Here’s the build page https://www.rckeith.co.uk/cnc-hawker-hurricane/
This article and the video series should help you to get started with DevFus Foam 2. It’s not the easiest software to learn and the documentation is OK but more of a reference than a tutorial. We are going to build a BAE Hawk jet with a 64mm EDF fan. It’s also developed for the US Navy as the T45 Goshawk.
Of course you can always buy one and they do look good and fly well. But if you crash, it can be hard to repair if that’s possible. Building your own if that happens means you can remake any broken parts.
How does DevFus Foam 2 work
We start off with a drawing of our intended model. This can be a CAD drawing in DXF format or an image file, such as jpeg. Several image formats are supported.
The image is imported, top and side views and then we calibrate it to our desired size. Once we have the image DevFus Foam 2 creates outlines of the top and side views, but these usually need to be manipulated.
We are then asked for the size of foam to use and from that the formers are generated. Unless it’s a very simple design these will most likely need some work. The first video is an overview and shows the basic operation.
Once we have the formers we have some options for spars, lightening holes and sheeting. DevFus Foam 2 introduced wing and canopy slots options. On my Hawker Hurricane I had to make a template for the wing slot and eyeball it on the fuselage and cut out the recess for the wing. It was a bit tricky but worked out OK.
What do we need to get started.
- DevFus Foam 2
- CNC Foam cutter with a control board
- Windows Computer 32 or 64bit
DevFus Foam 2 isn’t free software but you can download the full version and use nearly every feature. The only thing you won’t be able to do is generate the g-code. For that you will need a license. Check http://www.devcad.com/eng/prices.asp . It’s not the cheapest software but I haven’t found anything that’s come close. Version 2 has some extra features such wing and canopy slots.
Hot Wire CNC foam cutter – If you don’t have one yet then I have a series of articles and a free e-book. This has all the details, plans and parts list.
This video is an overview so you can see how the applications works without too much detail.
This video starts at importing an image, our BAE Hawk and then covers creating the outlines of the fuselage. The formers are generated and then we use some section cut images of our Hawk to get the jet intakes looking good. The is probably where you will speed the bulk of your time. Quite a long video around 45 minutes
In this video I cover a quick tip to help align the formers with the image and then go one to create the wing and canopy slot. I then show how to generate the g-code for one of the foam blocks.
These are the foam parts of the fuselage made CNC foam cutter.
Video is out I’ve released the g-code here for the fuselage parts http://www.rckeith.co.uk/free-gcode-to-make-fuselage-and-wings/
Here are some suitable car battery chargers like I’ve used in the video to cut the foam to the correct size
Canopy and Wing/Tail slots
The Canopy and Wings/Tail slots were a little challenging and I did have an issue with the wing slot, which almost ruined 3 blocks. The slot used the MH45 airfoil profile but came out too small. After a lot of investigation i turned out to be the kerf value (the amount of foam melted by the hot wire) causing the small size. I did contact Stephano at DevCad and explained the issue and here’s a link to the
After some testing with scrap foam I tried with a kerf value of 0 and this fixed the issue. It seems the inverse of what you would expect.
The jet intake ducts were the next challenge. To make these I created two templates using the DXF file you can export from DevFus Foam as a starting point. After that I used DraftSight to trace around the intakes of the reference image and copied these on the DXF file. Almost there!
Initially I printed these out and pasted to some thin plywood and started cutting out by hand, which didn’t look great. Why don’t I use my CNC router, that’s what it’s for making parts like this, doh. So I imported the DXF into Fusion 360 and created the g-code. The templates came out well and these were stuck to the former in front of the EDF.
Using a bow with a ni-chrome wire passing about 3 Amps was enough to allow me to follow the template manually and get the results below. Quite pleased how they came out.
The wings can be made with free software such as JediCut and David the Swarfer G-code generator. I have article and a video on these
The companion program to DevFus Foam 2 is DevWing Foam http://www.devcad.com/eng/devwingfoam.asp This is paid software but I haven’t upgraded to this yet, the pervious version was Profili 2 Pro which I’ve used many time to make foam wings. So I will probably use this.
Part 6 Assembly
Here’s the video update on the assembly. Going together quite well with the wings covered in brown paper and PVA and will then be covered in white solarfilm. Fusealge is going to be covered with lightweight fibreglass cloth and Poly-C. I’ve decide to finish the Hawk as a US Navy T43 Goshawk
Test Flight – coming soon
I’ll make a video on the